HPI Racing 1/10 Sprint 2 Drift 2010 Camaro RTR

This is the 1/10 scale, electric powered, 2.4GHz radio controlled, RTR HPI On-Road Sprint 2 Drift Car with the 2010 Chevrolet Camaro Body.

FEATURES

• Chassis: 3/16" (4mm) thick plastic
• Drive: Four wheel belt drive
• Motor: Firebolt 15 turn brushed
• Radio: 2.4GHz with waterproof steering servo and waterproof receiver box
• Electronic Speed Control: HPI SC-15WP LiPo compatible, waterproof and reversible
• Battery: 7.2V NiMH 2000mAh
• Battery Charger: AC wall type
• Ball Bearings: Full set included
• Shocks: Oil-filled, plastic bodied with special drifting springs
• Differentials: Planetary gear with metal outdrives
• Transmission: Single speed
• Tires: Falken Azenis hard plastic drift tires, width 1.02" (26mm), 2.5" (63mm) diameter
• Wheels: Officially licensed 5-spoke Rays Volk wheels with 6mm offset,
• outer diameter: 1.9" (48mm), width: 1.0" (26mm)
• Pinion Gear: 28 tooth 48 pitch metal
• Spur Gear: 48 pitch, 87 tooth, composite construction
• Body: Painted and trimmed 2010 Camaro
• Bumper: Front, foam
• Suspension: Fully adjustable
• Ackerman: Adjustable, Ackerman describes the effect of the inner front wheel turning faster than the outer front wheel during turns
• Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis
• Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle
• Steering: Ball race bell-crank type with servo saver
• Warranty: Two year limited warranty through HPI beginning at purchase date. Valid only in the USA, Canada and South America

INCLUDES

• HPI On-Road Drift 2010 Camaro with motor
• electronic speed control
• painted body
• drift tires
• wheels
• 28 tooth pinion gear
• AA batteries for radio
• 2000mAH battery
• wall charger
• 87 tooth spur gear
• 2.4GHz radio
• steering servo
• decal sheet
• 15T motor
• instructions

REQUIREMENTS

• Misc. Items: Building and track equipment

SPECIFICATIONS

VEHICLE

• Length: 17" (431mm)
• Width: 7.5" (190mm) - 8.0" (190mm) adjustable using offset wheels
• Height: 5" (127mm)
• Wheelbase: 10" (255mm)
• Front Track: 7.38" (187.5mm) side to side at outer edges of wheel
• Battery Charger: To match selected battery
• Paint: Polycarbonate safe spray or brush-on
• Misc. Items: Building and track equipment
• Front Tread: 6.5" (166mm)
• Rear Tread: 7.2" (183mm) side-to-side at wheel centers
• Ground Clearance: 0.5" (13mm)

BODY

• Length: 17.1" (434mm)
• Width: 7.75" (197mm) at rear wheels (widest point) 6.6" (169mm) behind from wheels (thinnest point)
• Height: 4.4" (111mm)

COMMENTS

For Replacement Ball Bearings use:

• Qty. Size Location Qty. Bearing Set
• 4 5x10mm Fr Wheels 2  DTXC1535
• 4 5x10mm Rear Wheels 2  DTXC1535
• 2 10x15mm Fr Diff 1  DTXC1595
• 2 2x8mm Fr Diff 1  DTXC1523
• 2 10x15mm Rear Diff 1  DTXC1595
• 2 2x8mm Rear Diff 1  DTXC1523
• 2 4x8mm Servo Saver 1  DTXC1511
• 2 4x8mm Middle Lay Shaft 1  DTXC1511